solbear

“1kW within 1hr” isn’t power. That’s energy.

The watt is always power, not energy. I'm assuming OP here got some prepositions mixed up and meant 1 kW delivered for 1 hr. That amounts to an energy of 1 kWh.

The second is like hell hole, tons of energy but still only a little bit of power.” No. They are both precisely the same energy.

No, they are the same power. The energy in the case where 1 kW of power is delivered for 1 hour is 1 kWh. The energy in the case of 1 kW delivered for 1 s is about 0.28 Wh.

If instead 1 kWh was transferred over the course of 1 hour, that is an average power of 1 kW (but does not have to be uniform, without more information we can't know the power profile). If 1 kWh is transferred over the course of 1 s, that is an average power of 3.6 MW which is the example I think OP was getting at (ref. hell hole comment).

Thanks for that explanation! :)

Is this a general purpose WebDAV-server? I'm looking for something to use as my Zotero file storage (nearning the point I have to spend $120 for it every year), but as of now, I know nothing about WebDAV.

Also not sure how I understand what it means that it is compatible with Nextcloud. Is it so that my Nextcloud server uses WebDAV as file storage, and I can use this to connect to that? I have kind of been thinking about ditching Nextcloud in favor of more specialized services for the stuff I use Nextcloud for (file sync, photos, calendar, contacts and cospend).

What are you referring to when you say "salt batteries"?

In this case, C refers to the current rate, not the unit Coulomb. It is a standard way of giving the current rate in battery research, and 1C is defined, as oldfart says, as the current rate required to charge that particular battery fully (to its nominal capacity) in one hour. 2C is twice this, so it is charged in half an hour, and C/2 is half this, so it is charged in two hours.

It is a convenient way of giving the current rate, because it allows a more application focused comparison (i.e. my EV battery or phone battery should be able to charge fully in one hour), but it hides the actual capacity of the battery (you have no way of knowing, without additional information, if the cell has a small or a large capacity).

ETA: The last point here is what deranger and AwesomeLowlander is getting at. You can have a very small battery with very little active material, and charge that at 10C and achieve reversible cycling for many, many cycles, and it is meaningless if it cannot be scaled to a larger cell (unless we are only considering microbatteries for example). Usually, results at a small scale is not directly transferable to larger scale, and you encounter all kinds of challenges as you scale up.

I have the same, a little over 8 years now. Always happy. Reminds me I should oil the handle soon.

I've been using a Merkur Progress for ten years now. The adjustability of the action makes it more versatile, which makes it easier to adjust to different types of blades. I use Astra Superior blades, but also have a stack of Shark blades that I at some point liked, and some Feather blades that are insanely sharp and unforgiving.

Make sure you learn how to lather properly. A good lather makes all the difference, and it also a major factor in making it a lot more enjoyable than the canned Gillette-stuff. I use Proraso for my run-of-the-mill shaves, and have over the years bought a variety of hard soaps as well. My favorite is Marlborough from D.R. Harris.

EDIT: I had one of those starter razors from Mühle in the beginning (Rytmo?). It snapped in two at the neck after I dropped it by accident, after 6 months use. I still have the synthetic hair brush that came with it. Some people go really into brushes, but I've been happy with mine.

Thanks for the suggestion. I think it would be difficult to maintain water in both, and I don't have too much leeway in terms of height differences either.

The end outside of the container can have any number of means to attach a hose or pipe; like a barb, flange, thread, etc. For your application you will want a barbed bulkhead so you can just put a hose on there and don’t need to worry about the additional cost and work involved with rigid pipe.

Ah, I've seen those kinds before, and that seems fairly simple. Thanks!

As for the stain issue. The type of container you described leads me to believe it is a typical plastic storage box, almost all of those have a taper to the sides.

Of course, now I understand what you meant! Yes, the boxes are slightly tapered, so that would be an issue.

Tube and barbs also have the benefit of being easier to connect across a short distance and ensure a watertight connection. I would recommend putting the tube on both sides first, then installing the bulkheads in the containers to make life easier and avoid damage when trying to press the tube on the barbs after the bulkheads are installed.

Great tips, noted! Now I'll have to figure out where I can buy these locally.

Thanks again for great help!

Thanks for a great description!

A couple of questions:

A bulkhead fitting should have a rubber gasket that will seal properly without additional sealant

Since bulkhead fittings were suggested, I've been looking them up. The installation seems easy enough, but in all the videos I see I am stuck with a hole with threads on the outside, no one shows what comes next. What are the parts I would need for this? Do I need a join to connect the threads on the outside of each container?

The sides of the container won’t be parallel to the ground, so a straight pipe will put strain on the container that will lead to a failure. You will probably want to use flexible hose to connect the two containers, but two 45 degree elbows at each end of ridgid pipe(so 4 total) can take the strain out once you play with the orientations.

I didn't really understand this. Do you mean there will be strain due to the downward force exerted by the weight of the pipe and water? I'm hoping to have the distance between the tanks as short as possible, and the diameter should also not be too big.

Cheers, I'll look into those! :)

Good idea, didn't think about that!