A handmade home for woodworkers and admirers of woodworkers. Our community icon is submitted by @[email protected] whose father was inspired to start woodworking by Norm and the New Yankee Workshop.
I would expect my battery powered circular saw to rip 3/4" oak. If your table saw has less huevos than this you might want to take advantage of the fact it's belt driven and replace the motor.
I've been using a combination blade made by DeWalt for most things including ripping and resawing white oak. It tends to leave some minor saw marks that I tend to remove with a 1/64" pass on my jointer or a lick with a bench plane.
Love my diablo blades, definitely an a-/b+ blade
I'll second the Diablo recommendation if you can drive down to the hardware store and pick one up off the shelf. Home Depot has them in my area.
If you're ordering online you have all the choices and I can't help you there.
I prefer a coarser 24-tooth blade for speed, and especially if you're going to be ripping stock thicker than 3/4". The finish it leaves it leaves is perfectly fine, and if you need it any smoother you can give it one pass with a plane. High-tooth-count blades are slow and it takes more effort to push the stock through.
I have a 60 tooth 10" Diablo blade in my table saw and haven't had any complaints. My use case is mostly home diy projects, primarily with fir/pine and plywood, but I have ran oak through it without any issues.
Given the price difference you are seeing I would get the Diablo blade and try it out.
I think a big part will be knowing your saw, how quickly it wants to cut (regardless of the blade) and making sure it isn't overloaded by exceeding how quickly it wants to cut.
Freud, which also makes Diablo, has quite a few good options. Go for something with less teeth (like a 24T) which will give a smooth cut without overloading the saw. The 113 should handle hardwoods over 3/4" just fine.
I believe it was StumpyNubs @ youtube who recommended Ridge Carbide, but they're expensive. https://ridgecarbidetool.com/collections/table-saw-blades/products/10-x-40t-ar-4-1-15-hk-094-125-ts2000-super-combo-blade
I haven't used them yet but I'm definitely buying one when I need another blade.
Heat kills the blade, and longer rips will cause the blades to get hotter than short rips. These carbide blades are supposed to do really well at staying cool.
I’ve seen his recommendation too but that’s another 2x price jump over the price range I’m already trying to avoid!
High quality blades can be professionally sharpened multiple times. Blades from Big Box stores generally cannot. That being said, Diablo's are fine for home user, IMO.
I forgot exactly how expensive they were when I posted. Sorry
I really like CMT Orange blades. I had a 2 year old blade that seemed to have a defect in the finish and when I contacted them, they immediately asked for my address to send a replacement blade.
Once again confirming the Diablo. My only real experience is with stock or Diablo. 90t 10" Diablo does plywood without affecting veneer. I use the stock (newish) delta blade for ripping though. Id think Diablo would make a good ripper with how well it does finer work.
90t 10" Diablo does plywood without affecting veneer.
Well now I know what else I'm buying on my next trip to the hardware store...
In think this CMT orange blade is a good value for the table saw https://www.amazon.com/CMT-256-050-10-Industrial-Combination-Grindwith/dp/B000P4NTRC
diablo 40+ tooth
Why not a 24t for ripping?
you can use a 24t, but the 40t can do more accurate finer rips and lasts a bit longer in my experience, and it can handle hardwoods better, and reduces splintering etc when ripping plywood. if doing cabinets maybe go up on teeth even more, but then youre pushing the balance of cost and performance.