galaxi

Surprised I haven't seen this, but have you tried a different cable? Display port? Could be worth a shot.

It's much easier said than done, but perhaps you should be putting more energy into your relationship with yourself too, not just with her. Sometimes these issues arise as a side effect of the people in the relationship not taking good care of themselves and their life. Imagine getting yourself to a place where you feel confident again and secure despite whatever might happen between you two. Working on that magnetism created by self-fulfillment and self-focus might invite your gf to feel freer and more inspired to start pursuing and desiring you again. I don't mean play games, but just create a bit of space to recreate some of the desire.

Keep in mind it might not be in your control if it doesn't have anything to do with you. Your gf might be struggling with hormones, body image issues, stress, depression. Sometimes you get used to being in a relationship and take it for granted a little too (especially if she feels like the option is always there). If you pull back from always being open to sex, create a bit of scarcity, and show focus on your own happiness and your own life outside her, it might help her to feel less stressed and find her way back to you. It's understandable to feel unstable about things and it sucks that it sounds like she isn't working on things together with you, but maybe she's just not there yet. Give it a little time and trust that you're doing as much as you realistically can for the relationship.

The 2 is a purge line, meant to clear any pressure in the nozzle and wipe it off before a print. It can be edited in your Start G-code on the printer settings tab > custom g-code on prusaslicer.

The 1 is a skirt, meant to get rid of any last few hanging bits of filament and start a clean print (sometimes the purge line doesn't get everything off the nozzle). It can also be used to gauge any last minute adjustments to your z offset. If the nozzle is too close or too far, you'll know before the print actually starts. I find that the skirt can be disabled if you're using a brim, since it's redundant at that point. Some who have fine tuned printers may opt not to use one at all without much issue. It isn't meant as any kind of draft shield as another person said - that's a separate setting. It's just a failsafe for the cleanest prints possible, avoiding hanging bits of filament, blobs from built up pressure, and incorrect z height. The first layer is the most important so everything that helps the first layer helps the rest.

This sounds eerily like the motto of conspiracy theorists when you start to ask too many questions.

You call also find silicone air fryer liners online!

Not as fast as I've been spending 😇

Doubtful. The main reason I could see a 3D printer starting a fire is either thermal runaway, often caused by bad software (on cheap printers) or electrical issues. You can check your wiring and make sure that nothing looks loose and all of your cables are in good condition. You can also make sure that your printer firmware is up to date. It's a Prusa right? I think you should be safe from software failure in that case, as they're quality.

If you're really concerned about it, you can also move your power supply, and even your mainboard, outside of the enclosure by using longer cables. This would keep the majority of the electrical components away from the foam and heated box. From my position I don't see an issue, but that's my personal opinion -- not legally accountable information. I will say that Stefan on CNC Kitchen uses foam as well, to get rid of ringing in prints. If you decide to go through with it, just use common sense and check to see if anything is hot. You might also get some benefit out of looking into silent stepper motors/drivers and trying to make the printer itself quieter.

I think you're right to complain, but at the same time, aren't single use plastics much lower on the pollution scale than, say, the fishing industry or other industrial plastic pollution? It makes sense to reduce and reuse, I try - but also find it beyond helpful to have a bunch of (unorganized) baggies strewn about for things like loose screws, storing filament spools, organizing USB cables, etc. I could definitely use something like this instead of a black hole under my sink. I know it's easy to judge -- esp without the whole picture -- and hopefully people aren't polluting willy nilly, but curiosity is a better approach than judgment or shaming when it comes to changing minds, wouldn't you agree?

I really enjoy the podcast Deeper Dating. The host, Ken Page, is one of the most emotionally in-touch men I've heard from. More so than a lot of women, honestly. Also, therapy and men's groups are a great start too. Consider poetry, talks from Brené Brown, books on attachment styles, and engaging with more emotionally intimate people in your life - even just as friends, male or female.

I was just thinking about this the other day. It's weird how Google has become so unusable due to its own practices that it seems to be giving up on being a search engine. I've been getting spam pop-ups lately on mobile search asking me to use AI. Of course people will wanna use it, they can't find their answers normally anymore. You search for something and it'll show you something completely unrelated because it's trying to be "helpful" and corral you towards buying shit, and it doesn't even do a good job at that. Heaven forbid you start to look past the first 3 pages.. I don't have a clue how these websites in the search results are maintained when they're filled solely with spam and nonsensical gibberish. I'm totally with you. We used to actually see communities around and now it seems like they've fallen into the dark web, unfindable except by means of knowing someone who knows someone or, frustratingly, reddit. Paradoxically, it's like the random AI-generated hash from the dark web is now here clogging up the tubes. I feel like everyone else came along and started dumping trash everywhere because we didn't put up any signs or make any rules not to litter.

Never heard of this before but it's fascinating. I think I found my next religion.

This is just one perspective, but people-pleasing is when you go overboard with being considerate of others -- to the point that you lose yourself. So like the one friend who will say they like all the same things as you, say yes to everything, never disagree, etc. just because they desperately need you to like them. They don't have boundaries, so even when someone hurts them, they're like "it's okay, I don't mind!" They're missing a bit of self-respect.

There's nothing wrong with being kind or considerate of others! It's really important to have to form deeper relationships. The problem is when seeming 'nice' takes the place of your personality or being honest about your real self, because you value other's validation more. People can sense that and it can put them off because they want to get to know the real person. People-pleasers can play the character that they think others want them to be, instead of putting in the work to like and value themselves and communicate their own needs and boundaries.