Machinist

Been getting slow loads and timeouts all morning. Figure it will probably resolve on its own. Didn't see any reports. Running Jerboa 0.0.77-gplay.

My son is about ready for his first printer. His school is running Cetus MK3 printers, he has a class using them, and his teacher has recommended this printer. He also has an educational seat of Fusion 360.

I'm proficient with Mastercam and hand written/modified G-code. I can help him with CAD no problem. Alignment, assembly, adjustment, and backlash are second nature for me. Have a little better than layman's understanding of printers. (Lusted over the Markforged printer that could do continuous carbon fiber.)

Eventually, will be building my own shop and hope my son might work with me. Hope to include printing, especially in metal.

I've seen some of the flap about Bambu and them closing up the software tool chain. I would like to avoid that sort of thing, for now, openness is better.

Top of my budget is around $500, with $200 probably being better.

Usable prints for tooling/spacers/repairs would be a bonus as would being able to print UV resistant plastic.

My goal for him is to get gud at modelling and get a feel for computer controlled movement. Another goal, harder to describe, is him finding the joy in mechanical tinkering and producing an idea made physical.

Thank you much! What do?

Any of y'all got a tracker that is following which portions of Project 2025 have actually been enacted? Something like the chump lawsuit tracking? Not finding anything with a search.

Does anyone know about Syrian Latakia tobacco?

It's a major component in English and Balkan style pipe tobacco. It has been replaced by the inferior Cyprian Latakia tobacco.

They hate each other so much.

Just looking up some DIY medical procedures and then the unwanted AI goes off the rails.

Found this broken piece in the creek bank. Southwest Pennsylvania. Farmhouse was built in 1922. Coalmining country.

Would have been about 18" in diameter. There is a rough coating in the glaze on the inside and outside of the bowl section. Abrasive enough that I figure it served a mechanical purpose. There are three grooves on the rim that aren't symmetrical to each other.

There might be a makers mark in the center of the glaze inside but I can't make it out. There is also a light blue/green stain on the bottom that might be a mark.

Any ideas?

Celeb_pics appears to be some bot posting from whoischic.com. Cluttters up /all.

The electric PTO clutch on my 1969 mini tractor is dead and discontinued.

Original winding is aluminum 18 gauge. Manufacturer specs were 2.88ohms, 237 turns. The manufacturer specs didn't quite physically match what I found when I took apart the old clutch. If I understand this correctly, the 2.88ohms is the most important part and will pull 4.17 amps.

I just attempted a coil with 18 gauge copper magnet wire. I made it to the max dimensions I can get in the housing with a scramble wind. I'm getting 1.2 ohms, which would pull 10 amps or so. Not good.

Was able to get 187 feet given the resistance.

If I go with 20 gauge copper, assuming I can get 235 feet (1.26 * 187) and I should get 2.319 ohms. Probably get a little more than 235 feet and get the resistance up a little more.

What does this do to the strength of the magnetic field?

Would I be better off putting a power resistor in series with my 18 gauge coil?

Any advice greatly appreciated!

Another before:

It's green Vermont slate, figured out that it was originally painted black and marbled. Victorian thing, faux marble mantels. Fireplace is also Victorian faux, red brick, would have had logs and a red light. I'll be putting in a gas insert at some point.

Started at 220grit, and worked up to 1000. Finished with a 50/50 mix of boiled linseed oil and mineral spirits:

Didn't realize slate could be this pretty and figured:

So, I found this stone mantel behind the garage of the 100 year old house we just bought. It was mostly buried in the dirt. Fits our mantel perfect. Some sort of green stone. Was painted black at some point. I'm trying to strip the paint and want to refinish the stone. Area is southeast of Pittsburgh. Father of the man who built the house was an Italian stonemason that immigrated.

Don't think it's slate, has a tight grain and rings when you knock on it.

What kind of stone is this?

Cishet male. In no way do I mean offense or have I tried to take advantage of lower functioning individuals, that's just sick. Best I can figure, I'm a typical. Maybe I'm a little crazy; but who isn't.

During a discussion about my son's neurodivergency, I realized I have a 'type' of woman. (Son is technically stepson, but he's my boy.) I tend to be attracted to high functioning women that are on the spectrum.

I've been in four relationships with divergent women, three serious and two extended friends with benefits. I've been in two serious relationships with typical women. Many flings with typical women. Figure that's pretty statistically unlikely.

In my experience, divergent women tend to have a refreshing openness in communication. Painfully honest. Direct. They have some weird stuff that can be alternately cute and irritating. When sleeping they either don't like to snuggle or like being an octopus. (My preference is octopus but my wife only tolerates some side contact.) They like to discuss instead of argue. Sexually adventurous and willing to work for satisfaction. They prefer precision in statements. I find myself writing in an extended way that I don't engage in with other people and try and pay attention to grammar and punctuation. Pretty sure this doesn't apply to all women on the spectrum, just my 'type'.

I dunno, just a strange realization, especially at this stage of life. It's not a fetish, just something that has occurred.